Window SpecSubmittal Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
SECTION 08 52 00—ALUMINUM REPLACEMENT WINDOWS
(Filed Sub- Bid Required)
PART 1 - GENERAL
1.01 FILED SUB-BID
A. Section 08 52 00-Aluminum Replacement Windows is stipulated as a Filed Sub-Bid
under Part D, Item 2 of the Form For General Bid.
B. All sub-bids shall be submitted electronically as set forth in the Instructions to Bidders
and as required by Section 44F of Chapter 149 of the Massachusetts General Laws, as
amended.
C. Sub-bids must be filed with the Awarding Authority, before 2 PM, Boston time, on the
date stipulated in the Advertisement.
D. Specific information relating the sub-bidders is set forth in the Contract Documents,
under the heading " Notice to All Bidders, including Sub-Bidders" and the attention of
sub-bidders is directed thereto.
E. Work to be done under this Section 08 52 00- Aluminum Replacement Windows is
shown on the Drawings numbered: A1, A2, A3,A4,A5, A6, A7,A8, A9 and A10.
1.02 PROVISIONS INCLUDED
A. The general provisions of the Contract including the General and Supplementary
Conditions and applicable portions of Division 1 - General Requirements apply to the
work of this Section.
1.03 DESCRIPTION OF WORK
A. Provide all aluminum replacement windows complete, in place, as shown, specified here
or required for a complete and proper installation. Work includes, but is not necessarily
limited to:
1. Aluminum master frames for fixed glazing and operable sash.
2. Aluminum single hung, and project out window units and hardware.
3. All glazing for aluminum frames and windows.
08 52 00- Aluminum Replacement
Windows
Page 1
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
4. Exterior and interior perimeter caulking at new aluminum replacement windows.
5. New rubberized sill flashing as detailed.
6. All aluminum window trim including structural vertical mullions, snap trim caps,
sub-sills, and fasteners in the same color to match the windows.
B. Related Work Specified Elsewhere:
1. Demolition of old aluminum windows.
2. Masonry restoration.
1.04 QUALITY ASSURANCE
A. Reference Standards:
1. Except as otherwise indicated, the requirements for aluminum windows, and the
terminology and standards of performance and fabrication workmanship, are
those specified and recommended in ANSI/AAMA 101-85 and the applicable
general recommendations published by AAMA, NAAMA and AA.
B. Manufacturer:
1. Unless formal approval is granted by the Architect prior to the sub-bid due date
which shall be based upon a preselection examination of proposed products,
window units shall be by one of the following approved manufacturers:
a. Graham GT 2200 , GT 6200, and GT 140011;
b. Skyline
C. Wausau
d. or approved equal.
2. The details shown are based upon standard details of an acceptable manufacturer.
Similar details by other manufacturers will be acceptable,provided they comply
with the size requirements shown.
C. Certification:
1. Provide only aluminum window units which have the AAMA "Quality Certified"
label attached.
08 52 00-Aluminum Replacement
Windows
Page 2
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
2. Wherever manufacturer's standard units comply with requirements and have been
tested in accordance with the specified tests,provide certification by the
manufacturer of compliance with such tests; otherwise,perform the required tests
through a recognized testing laboratory or agency and provide certified test
results.
D. Field Measurement: Take field measurements at all openings and build windows to
conform to actual field conditions.
E. Performance Standards: The window assemblies shall conform to the following
standards:
1. Fixed Windows: Fixed windows shall meet or exceed the following performance
standards:
a. AAMA Rating AW-PG65
b. Air Infiltration .12 CFM/ft @ 50 mph
C. Water Infiltration 12 psf
d. Structural: 97.74 psf
e. U-Value: .35
2. Operable Windows: Projecting windows shall meet or exceed the following
performance standards:
a. AAMA Rating AP-HC70
b. Air Infiltration .06 CFM/ft @ 25 mph
C. Water: 12 psf
d. Structural: 135 psf
e. U-Value .35
3. Samples:
a. Submit 2 samples of each required aluminum finish on 12 inch lengths of
extrusion shapes as required.
b. Submit one complete operable window sample which will show the
fabrication techniques and workmanship of component parts, the design of
hardware and other exposed auxiliary items for window units, before
fabrication of the work.
1.05 SUBMITTALS
A. In accordance with submission requirements set forth in Division 1, submit:
08 52 00-Aluminum Replacement
Windows
Page 3
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
1. Manufacturer's Data: Submit manufacturer's specifications, recommendations
and standard details for aluminum window units, including fabrication, finishing,
hardware and other components of the work. Include certified test laboratory
reports as necessary to show compliance with the requirements.
2. Shop Drawings: Submit shop drawings for the fabrication and installation of
aluminum window units and associated components of the work. Include typical
unit elevations at 1/2 inch scale, and full size detail sections of every typical
composite member. Show anchors, hardware, operators and other components
not included in manufacturer's standard data. Include glazing details. Show
details of panning system.
1.06 ADDITIONAL MATERIALS
A. Provide the following extra materials for the Owner's use in maintaining the windows.
Store materials in protective crates where directed by the Architect.
B. Schedule of Additional Materials:
1. Sash: Upper and lower units equal to 2% of
each size installed (round
fractional units up)
2. Hinges: Five sets of hinges for each type
of window provided.
3. Hardware: Twenty locks and handles with fasteners.
4. Touchup Paint: One gallon matching specified finish for infill panels and
louvers.
1.07 COORDINATION
A. As part of the work of this section, the window subcontractor is responsible for
coordinating the work of this section with the removal of the existing windows. At no
point shall window openings be left open overnight. All new windows shall be installed
at locations of removed windows within the same working day.
B. The work of this Section will be required to conform to the construction phasing as noted
in Article 1.16 of Section 01010—Summary of Work.
08 52 00 -Aluminum Replacement
Windows
Page 4
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
1.08 STAGING
A. It is anticipated that the new windows will be installed from within the building,
however; if exterior access is required to install the windows and to complete the exterior
perimeter caulking, all lifts, hosting, and/or staging required will be the responsibility of
the contractor.
B. No permanent or fixed staging will be allowed in the two alleyways. These alleyways are
public and free access must be maintained at all times.
PART 2 -PRODUCTS
2.01 BASIC MATERIALS AND COMPONENTS
A. Aluminum Extrusions: Alloy and temper recommended by manufacturer for strength,
corrosion resistance and application of required finish, but not less than 22,000 psi
ultimate tensile strength and not less than 0.062" thickness at any location for main frame
and panel members.
B. Fasteners and Accessories: Aluminum, stainless steel or other metallic or nonmetallic
materials guaranteed by the manufacturer to be non-corrosive and compatible with the
aluminum members,hardware, anchors, and other components of the units. Provide
angles, shims, anchors, stops, fins and other accessories required for complete
installation.
C. Hardware: Cast, wrought, or drop forged aluminum, non-magnetic stainless steel, or
white bronze where exposed. Provide hardware items necessary to properly operate,
tightly close and securely lock windows. Do not use aluminum in frictional contact with
metal.
D. Sealant: Unless otherwise indicated, for sealants required within the fabricated units,
provide type guaranteed by unit manufacturer for the joint size and movement to remain
permanently elastic, non-shrinking and non-migrating.
E. Glass: Provide manufacturer's standard 1 inch units of 2 sheets of 1/a" clear plate glass
(ASTM C-1360, Type I, Class 1, Quality q3); permanently and hermetically sealed
together at edges with spacers and sealant to provide a dehydrated air space with -60
degree F. dew point. Provide dual seal construction with soft coat low E type glazing.
F. Glazing Beads or Stops: Manufacturer's standard glazing beads or stops to suit required
glass thickness. Provide continuous vinyl channel type, of color to match aluminum, or
extruded aluminum glazing stops with integral vinyl glass seal or vinyl channel type
08 52 00-Aluminum Replacement
Windows
Page 5
Window Replacement-Zisson Building
Salem Housing Authority
Salem,MA 01970
glazing bead inserts. Precut beads or stops to full-length pieces as required, for neat fit
and tight weatherseal.
G. Safety Glazing: As required by the Massachusetts State Building Code, 8d'Edition.
2.02 ALUMINUM OPERABLE WINDOWS
A. General: Provide thermal aluminum operable windows meeting heavy commercial grade
AAMA Rating AW-PG65.
B. Frame: Provide frame of.125"nominal material wall thickness of 6063-T5 or T6 alloy
with a depth of between 4". Corners are of screw spline construction and back sealed
with small joint seam sealer. Frames are to include extruded sills and stools as detailed.
C. Vent Frame: Provide frame with .125" nominal material wall thickness of 6063-T5 or T6
alloy with a depth of 2". Comers are mitered, angle reinforced, crimped, and cold epoxy
welded, and back sealed.
D. Hardware: Provide the following:
1. Hardware having component parts which are exposed shall be of aluminum,
stainless steel or other non-corrosive materials compatible with aluminum.
Cadmium or zinc plated steel where used must be in accordance with ASTM
Specifications B 766 or B 633.
2. All primary locking devices shall be cast in white bronze cam action locks. Two
such locking devices shall be required when vent height exceeds thirty inches.
Cam lock handles on projected units shall be "handed"to facilitate operation.
The left lock to sweep left, the right lock to sweep right.
3. Projected ventilators shall be balanced on two heavy duty stainless steel hinge
assemblies. Hinge shall have the ability to open the window to 90 degrees for
easy cleaning. Nylon slides with a suitable set screw shall be provided for
precision adjustment.
E. Weatherstripping: Provide dual weather stripped Neoprene leaf or bulb gasket types.
Weatherstripping shall allow for internal weep system to drain.
F. Glazing: All units (except insulated panels as required for insulation) shall be pre-glazed
with an exterior continuous uniform silicone bread with an interior snap on aluminum
08 52 00-Aluminum Replacement
Windows
Page 6
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
bead containing a rigid back bulb gasket installed at the factory with the specified glazing
material as follows (use of tapes, vinyls, or any other type of sealant is not allowed):
1. Typical insulated glass shall be constructed to an overall thickness of 1"with two
liter of 1/8, 3/16, or 1/4". Typical 1"insulated glass units shall be dual seal. The
primary sealant shall be polyisobutylene applied to the edge of the spacer. The
secondary sealant shall be silicone. The air spacer shall be continuous metal
spacer with formed corners and an in-line connector, containing desiccant.
G. Screens: Provide screens on operating vents as indicated on the architectural plans.
Screen frames are to be extruded aluminum sections with corners mitered and
mechanically attached. Screening fabric shall be 18 x 16 aluminum mesh retained in
screen frames with vinyl splines that permit easy replacement. Screen frames shall be
secured by aluminum clips fastened with stainless steel screws into window frames.
Frames shall be finished to match windows or specify finish.
H. Mullions: Provide both vertical and horizontal 3-piece structural mullions, integrated
into the master window frame capable of withstanding horizontal loads without
deflecting more than 1/1751h of it's span.
I. Vent Stops:: At hopper and awning locations on the first floor,provide vent units with an
integral stop from preventing outer corner of vent from protruding beyond the edge of the
masonry wall. In general, this distance equals 4—6 inch projection from the frame.
J. Sub-sill: At all window frames,provide an extruded aluminum sub-sill at the base of the
window frame above the existing concrete or brick sill.
2.03 ALUMINUM FIXED FRAMES
A. Provide aluminum framed fixed glazing by the same manufacturer as the operable
aluminum windows and complying with the relevant portions of the fabrication
specifications above.
B. Provide mullions, sub-bucks sub-sills and accessory items to mount and join frames.
C. Muttins: Provide concealed type aluminum grids within the insulated glazing of hollow
aluminum in finish to match window system.
2.04 FINISHES
A. Windows: Provide a clear 2 coat Fluorpolymer 70% kynar finish meeting or exceeding
AAMA 2605 finish.
08 52 00-Aluminum Replacement
Windows
Page 7
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
2.05 SEALANTS
A. Movement Joints: Provide sealants at interior and exterior joints between new aluminum
replacement windows and adjacent materials including masonry and concrete.
1. At all perimeter window joints,provide a low-modulus one-part or two-part
polyurethane polymer- based sealant complying to Fed. Spec. TT-S-0O227E
Class A, Type II and equal to:
a. Tremco "Dymeric";
b. Pecora "Dynatrol 11";
C. Sonneborn "Sonolastic NPII";
d. or approved equal.
2.06 MISCELLANEOUS MATERIALS
A. Joint Cleaner: Provide cleaner recommended by the manufacturer of the sealant for the
specific joint surface and condition.
B. Joint Primer and Sealer: Provide compounds recommended by the manufacturer of the
sealant for the specific joint surface and condition.
C. Bond Breaker Tyne: Pressure sensitive polyethylene tape.
2.07 JOINT BACKER ROD
A. Provide resilient closed cell polyethylene foam joint backer rod manufactured specifically
for cold-applied joint sealants.
B. Provide rod sized 1/8" to 1/4" larger in diameter than joint for which it is intended to
ensure its being under compression.
2.08 MEMBRANE AT WINDOW SILLS
A. Provide a high strength rubberized asphalt sheet membrane waterproofing equal to:
1. W.R. Grace "Bituthene";
08 52 00-Aluminum Replacement
Windows
Page 8
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
2. Polyguard Products, Inc. "Polyguard 650 membrane";
3. Pecora "Duramem 700-SM";
4. or approved equal.
B. Follow manufacturer's printed recommendations for materials required, application of
membranes and terminating membranes. Provide all materials for a complete
installation. Turn flashing up 4 inches at jambs behind window frame.
PART 3 -EXECUTION
3.01 INSPECTION
A. Examine the substrate and conditions under which the aluminum window units are to be
installed and notify the Architect in writing of conditions detrimental to the proper and
timely completion of the work. Do not proceed with the work until unsatisfactory
conditions have been corrected or formally waived.
3.02 INSTALLATION OF WINDOWS
A. Comply with manufacturer's specifications and recommendations for the installation of
window units, hardware, operators, and other components of the work.
B. Set units plumb, level and true to line, without warp or rack of frames. Anchor securely
in place. Separate aluminum and other corrodible metal surfaces from sources of
corrosion or electrolytic action at points of contact with other materials.
C. Set sill members and other frame members in a bed of compound or with joint fillers or
gaskets, to provide weathertight construction.
3.03 ADJUST AND CLEAN
A. Adjust operating panels and hardware to provide a tight fit at contact points and at
weather stripping for smooth operation and weathertight closure.
B. Clean aluminum surfaces promptly after installation of window units. Remove excess
glazing and sealant compounds, dirt and other substances. Lubricate hardware and other
moving parts. Remove glass labels after acceptance of window work and wash off
harmful soil.
08 52 00-Aluminum Replacement
Windows
Page 9
Window Replacement-Zisson Building
Salem Housing Authority
Salem,MA 01970
C. Advise Contractor of protective treatment and other precautions required through the
remainder of the construction period, to ensure that windows will be without damage or
deterioration other than normal weathering at the time of acceptance.
3.04 ACCEPTANCE OF GLASS AND REPLACEMENT
A. At conclusion of the work of this Section,present all glass for inspection by the
Architect. Architect will inspect glass for conformity with the Contract Documents and
recommend to the Owner acceptance of the glazing. After glass has been accepted by the
Owner, responsibility for protection of glass and replacement of broken glass shall pass
to the General Contractor. Prior to presenting glass for acceptance,remove labels and
clean glazing of gross soil, harmful substances and excess sealants.
3.05 FINAL ADJUSTMENT AND OVERALL ACCEPTANCE
A. At the conclusion of all construction work, but prior to final inspection of the project for
acceptance,return to the site and make all necessary final adjustments, clean tracks, oil
moving parts and leave all windows in perfect operating order.
3.06 PREPARATION OF SURFACES FOR SEALANTS AND CAULKING
A. Examine all joints to receive sealants or caulking compounds prior to application. Do not
commence work in any area where conditions exist which would adversely affect the
achievement of weather tight seals until corrective work has been completed or waived.
Starting of work in any area shall constitute acceptance of conditions in the area by this
Subcontractor, who shall from that time be responsible for the satisfactory results of his
work.
B. Clean joints and spaces to be sealed and caulked so they are dry and free of dust, loose
mortar, and other foreign matter. Wire brush joints in concrete and masonry and air-blow
or vacuum clean.
C. Clean all surfaces which have been given protective coatings and all those which contain
oil or grease with xylol or MEK solvent, with due precautions taken to minimize hazards.
D. Prime all surfaces where and as recommended by sealant or caulking compound
manufacturers.
E. All exterior joints shall be backed with joint backing material to eliminate back bond.
Where width of exterior joint is 1/2 in. or less,prepare joint to depth of sealant bead is
08 52 00 -Aluminum Replacement
Windows
Page 10
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
approximately equal to its width. Where width of exterior joint exceeds 1/2 in.,prepare
joint so depth of sealant bead is approximately equal to 1/2 its width or 1/2 in., whichever
is greater. Use appropriate joint backing and joint filler material as specified
hereinabove.
F. Backing of interior caulked joints will not be required except where depth of joint
exceeds 3/4 in., in which cases it shall be backed to that depth by use of compressible
foam, as above, or non-staining oakum.
G. Provide masking tapes or other precautions to prevent migration or spillage of materials
onto adjoining surfaces.
3.07 APPLICATION OF SEALANTS AND CAULKING
A. Application of caulking compounds and sealants shall be in strict accordance with the
manufacturer's printed instructions.
B. Apply sealants and caulking compounds before final coat of paint is applied to adjacent
surfaces.
C. Compound shall generally be applied by means of a hand gun, unless otherwise specified,
without smearing of adjacent surfaces, and with sufficient pressure and with proper
nozzle size to solidly fill all voids and joints. Where required by manufacturer's
instructions, sealant shall be heated to recommended temperature before application.
D. Immediately after application, tool all beads to ensure firm, full contact with the inner
surfaces of the joint. Strike off excess material with tooling stock or knife Finish all
exposed joints to smooth, even, wrinkle-free, slightly concave surface.
E. Pour self-leveling compounds in horizontal joints to a level approximately 1/16 inch
below adjacent surfaces.
3.08 CLEAN UP AFTER CAULKING AND SEALING
A. Remove smears from adjacent surfaces immediately as the work progresses. Exercise
particular care to prevent smearing or staining of surrounding surfaces which will be
exposed in the finished work. Repair any damage done to the work of other trades.
B. At the completion of the work of this Section, remove all packaging and debris from job
site. Remove all construction aids and tools and leave work areas neat and clean.
08 52 00-Aluminum Replacement
Windows
Page 11
Window Replacement-Zisson Building
Salem Housing Authority
Salem, MA 01970
3.09 CLEAN UP
A. Keep work areas clean by daily sweeping and removal of debris resulting from window
work.
B. At conclusion of job remove from job site all crates,packing material, scrap and other
debris.
C. Repair or replace work of other trades soiled or damaged by window installation work.
END OF SECTION
08 52 00-Aluminum Replacement
Windows
Page 12
Environmental Restorations, Inc.
A professional approach to gualihy service
General Contracting•Deleading•Sandblasting•Asbestos Removal•Mold Remediation •Fire&Water Restoration•Duct Cleaning
Submittals
Salem Housing Authority
Window Replacement-Zisson Building
1. GC and window fabricator to field
verify window sizes.
Owner: Salem Housing Authority 2. Coordinate issue found during
.27 Charter Street installtion of sample window.
'Salem, MA 01970 3. Window and panning color to be
,Contact: Debbie Tucker selected by the Salem HA.
Architect: Blacksone Block Architect 4. Please verify screen sizes and
7 Marshall Street, Suite 301 mesh type with the Salem HA.
,Boston, MA 02108
(Contact:Barry Bubchinski
General Contractor: Environmental Restorations,Inc
25 Spaulding Road,Suite 17-2
Fremont,NH 03044
Contact:Keri Minasalli(603)895-0400
Submittal Number: 085200-01-001
Product: Aluminum Replacement Windows: Multi
Manufacturer: Universal Window& Door
Architect's Stamp&Sign Off Contractor's Stamp&Sign Off
BSBA#08-01
❑ Approved ❑ Rcviseand Resubmit APPROVED t';OR CONFORMANct'
X Approved as Noted ❑ Rejected WITH THE CONTRACT DOCUMENTS
❑ Not Required by the Contract Documents All Dimensions and Quantities Have Bear,
Reviewed and Are Accepted by
Approval is only for conformance with the design concept ENVIRONMENTAL RESTORATIONS,
of the Project and compliance with the information given in the RATIONS,INC.
Contract Documents.Contractor is responsible for dimensions All Dimensions and Field Conditions Have Been
to be confirmed and correlated at the job tile:for infont:pion or will Be Verified PRIOR to Fabricators
that pertains solely to the fabrication process or to techniques of the Items Described Her
of construction:and for coordination of the work of all trades.
j-/ Herein
BLACKSTONE BLOCK ARCHITECTS,INC
By BB Date 01/24/2019
25 Spaulding Road,Suite 17-2,Fremont,NH 03044 •Tel (603)895-0400 • Fax (603)895-0445
www.environmentalrestorations.com
1���� Quotation
� � UNIVERSAL 3O3 Mechanic St. Marlborough, MA.O1752
.on Window and Door Phone:800.63www. 1 Fax:5windo 00 m
www.unlversalwindow.com
A full line of products for Commercial,Heavy Commercial,Institutional,Residential,Architectural and Historic Applications
Quote#: 11658
Billing Information: Shipping Information: Project: Salem Housing
Quote: ERI-#550 Creation
ERI-Environmental Restorations
Inc. Date:4/20/2018
292 Essex St Carrier:
25 Spaulding Road
Suite 17-2 Payment Terms:Customer
Fremont NH 03044 Salem MA Number:3367 PO Number:
Phone 603895-0400 Phone Fax::
Fax:: 603-895-0445
Order Comments:
Line I Qty I Product Description I Dealer Price I
Extended
100-1 4 TTT Frame Size: 36"
x 65"Notes: T
Mark: A
***PRODUCT'*'
Series 550 Double Hung Operable 36 x 65
Even Sash Split ,
**'SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum ffi
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top j
Balance-Block and Tackle,Bottom Balance-Ultralifts, Ll
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
36,65
—Wrapping Surcharges'**
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804 RJ,Tdm804@ Sill
Line I Qty I Product Description i Dealer Price I
Extended
100-2 4 TTT Frame Size: 36"x 65"
Notes:
Mark: A
MISC/TRIM 3
Line I Qty I Product Description Dealer Price I
Extended
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 1 of 26
200-1 4 TTT Frame Size: 36"
x 73"Notes:
Mark: Al
***PRODUCT***
Series 550 Double Hung Operable 36 x 73
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum e
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top 5 j
Balance-Block and Tackle,Bottom Balance-Ultralifts, L1
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
36,73
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804a RJ,Tdm804@ Sill
Line City Product Description Dealer Price I
Extended
200-2 4 TTT Frame Size: 36"x 73"
Notes:
Mark: Al
MISCITRIM 3
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 2 of 26
Line Qty I Product Description Dealer Price I
Extended
300-1 4 TTT Frame Size: 44"x
64 1/2"Notes:
Mark: B
***PRODUCT***
Series 550 Double Hung Operable 44 x 64 1/2 F 1
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh a
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left M
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
44,64 1/2
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
300-2 4 TTT Frame Size: 44"x 64 1/2"
Notes:
Mark: B
MISC/TRIM 3
Line Qty Product Description Dealer Price I
Extended
400-1 2 TTT Frame Size: 38"
x 44"Notes:
Mark: B1
***PRODUCT***
Series 550 Double Hung Operable 38 x 44
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum ,
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts, u
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
38,44
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ,Tdm804@ RJ,Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 3 of 26
Line I Qty I Product Description
Extended Dealer Price I
400-2 2 TTT Frame Size: 38"x 44"
Notes:
Mark: B1
MISC/TRIM 3
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 4 of 26
Line Qty I Product Description Dealer Price I
Extended
500-1 2 TTT Frame Size: 56"x
64 3/4"Notes: --,
Mark: B2
PRODUCT***
Series 550 Double Hung Operable 56 x 64 3/4 j
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum a
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top i I�
Balance-Block and Tackle,Bottom Balance-Ultralifts, lJ
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker**
55ODH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RILE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
56,64 3/4
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
500-2 2 TTT Frame Size: 56"x 64 3/4"
Notes:
Mark: 132
MISC/TRIM 3
Line Qty I Product Description Dealer Price I
Extended
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 5 of 26
600-1 6 TTT Frame Size: 31 1/2"
x 65"Notes:
Mark: B3 i
***PRODUCT***
Series 550 Double Hung Operable 31 1/2 x 65
Even Sash Split
*SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum a
Mesh
***HARDWARE*'*
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left r5
Jamb=Standard Jamb(400-103),55ODH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
**'GLASS***
Double IG,RILE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR**'
70%Kynar Finish,Window Color=Not Selected
31 1/2,65
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804P LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
600-2 6 TTT Frame Size: 31 1/2"x 65"
Notes:
Mark: B3
MISCITRIM 3
Line Qty Product Description Dealer Price I
Extended
700-1 2 TTT Frame Size: 33 1/4"
x 63"Notes:
Mark: B4
*PRODUCT***
Series 550 Double Hung Operable 33 1/4 x 63
Even Sash Split rY'
*SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
***HARDWARE*'*
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker**
550DH Header=Standard Header(400-101),550DH Left �3
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS'**
Double IG,RILE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR'*'
70%Kynar Finish,Window Color=Not Selected
33 1/4,63
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ Trim804@ RJ,Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 6 of 26
Line I City I Product Description
Extended Dealer Price 1
700-2 2 TTT Frame Size: 33 1/4"x 63"
Notes:
Mark: 134
MISC/TRIM 3
Line City Product Description
Extended Dealer Price 1
800-1 1 TTT Frame Size: 42"
x 44"Notes:
Mark: 135
***PRODUCT***
Series 550 Double Hung Operable 42 x 44 n
Even Sash Split 1�4
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
**HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,TopJ
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pale Op Sash Lock
***Extrusion Picker— 1
550DH Header=Standard Header(400-101),550DH Left -----,
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
42,44
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804 Sill
Line Qty Product Description
Dealer Price I
Extended
800-2 1 TTT Frame Size: 42"x 44"
Notes:
Mark: 135
MISC/TRIM 3
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 7 of 26
Line Qty I Product Description Dealer Price I
Extended
900-1 1 TTT Frame Size: 36 1/2"
x 44"Notes:
Mark: B6
***PRODUCT—
Series 550 Double Hung Operable 36 1/2 x 44
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left —------------
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RILE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
36 1/2,44
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804P LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
900-2 1 TTT Frame Size: 36 1/2"x 44"
Notes:
Mark: B6
MISC/TRIM 3
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 8 of 26
Line Qty I Product Description
Dealer Price I
Extended
1000-1 1 TTT Frame Size: 67"
x 44"Notes:
Mark: B7
***PRODUCT***
Row 1:Series 550 Double Hung Operable 33 1/4 x 44 71
Row 2:Series 550 Double Hung Operable 33 114 x 44 j1
Even Sash Split
***SCREEN*** :
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
*HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock ----
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RILE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
***MULLS***
Vertical Factory Mull 0.5 thick,44"length
67,44
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Trim804 Sill
Line City Product Description Dealer Price I
Extended
1000-2 1 TTT Frame Size: 67"x 44"
Notes:
Mark: B7
MISC/TRIM 3
Line Qty I Product Description Dealer Price I
Extended
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 9 of 26
1100-1 2 TTT Frame Size: 33"
x 72"Notes:
Mark: B8
***PRODUCT'*'
Series 550 Double Hung Operable 33 x 72 n
Even Sash Split
***SCREEN*** j
Standard Screen,Exterior Applied,Half Window,Aluminum a --
Mesh
***HARDWARE**'
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),55ODH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
''*COLOR'**
70%Kynar Finish,Window Color=Not Selected
33,72
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Tdm804 LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description
Extended Dealer Price I
1100-2 2 TTT Frame Size: 33"x 72"
Notes:
Mark: B8
MISC/TRIM 3
Line Qty Product Description Dealer Price I
Extended
1200-1 1 TTT Frame Size: 33 1/4"
x 72"Notes:
Mark: B9
***PRODUCT***
Series 550 Double Hung Operable 33 1/4 x 72 (j
Even Sash Split 4
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
***HARDWARE***
Auto Lock+Spring=*Yes,Full Length Rail=Yes,Top j
Balance-Block and Tackle,Bottom Balance-Ultralifts, lJ
Include Sash Lock=Yes,Pole Op Sash Lock
*Extrusion Picker'
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
33 114,72
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ Tdm804 RJ Trim804 Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 10 of 26
i,
Line Qty I Product Description Dealer Price I
Extended
1200-2 1 TTT Frame Size: 33 1/4"x 72"
Notes:
Mark: B9
MISC/TRIM 3
Line Qry Product Description Dealer Price I
Extended
1300-1 1 TTT Frame Size: 40"
x 39"Notes:
Mark: 610 --- ""
***PRODUCT***
Series 550 Direct Set Fixed 40 x 39
***HARDWARE***
Include Sash Lock=Yes
***GLASS***
Double IG,RILE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***Extrusion Picker**
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected
40,39
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
1300-2 1 TTT Frame Size: 40"x 39"
Notes:
Mark: B10
MISC/TRIM 3
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 11 of 26
Line Qty I Product Description Dealer Price I
Extended
1400-1 2 TTT Frame Size: 45 1/2"
x 57"Notes:Mark: B11
B11
PRODUCT***
Series 550 Double Hung Operable 45 1/2 x 57 (�
Even Sash Split j v
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh —
** HARDWARE—
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top r
Balance-Block and Tackle,Bottom Balance-Block andJ
Tackle,Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
45 1/2,57
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,TrinrI Sill
Line Qty Product Description Dealer Price I
Extended
1400-2 2 TTT Frame Size: 45 1/2"x 57"
Notes:
Mark: B11
MISC/TRIM 3
Line Qty Product Description Dealer Price I
Extended
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 12 of 26
1500-1 2 TTT Frame Size: 451/2"
x 57"Notes:
Mark: B12 1 —
***PRODUCT—
Series 550 Double Hung Operable 45 1/2 x 57
Even Sash Split
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Block and ij
Tackle,Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker*** i
550DH Header=Standard Header(400-101),550DH Left —K3
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
45 1/2,57
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804P LJ,Trim804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
1500-2 2 TTT Frame Size: 45 1/2"x 57"
Notes:
Mark: B12
MISC/TRIM 3
Line Qty Product Description Dealer Price I
Extended
1600-1 4 TTT Frame Size: 28"
x 56"Notes:
Mark: B13
***PRODUCT***
Series 550 Double Hung Operable 28 x 56 (�
Even Sash Split �}
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum x
Mesh
*HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Block and if
Tackle,Include Sash Lock=Yes,Pole Op Sash Lock 1
***Extrusion Picker**
550DH Header=Standard Header(400-101),550DH Left m
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
28,56
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ Tdm804 RJ Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 13 of 26
Line I Qty I Product Description Extended Dealer Price I
1600-2 4 TTT Frame Size: 28"x 56"
N otes:
Mark: B13
MISC/TRIM 3
Line Qty Product Description
Extended Dealer Price I
1700-1 4 TTT Frame Size: 33 1/2"x
56 1/2"Notes:
Mark: B14
------------
***PRODUCT*** I�
Series 550 Double Hung Operable 33 1/2 x 56 1/2 1
Even Sash Split c j
***SCREEN
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Block and
Tackle,Include Sash Lock=Yes,Pole Op Sash Lock I I
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left -
Jamb=Standard Jamb(400-103),550DH Right Jamb= j
Standard Jamb(400-103),550DH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RILE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***COLOR***
70%Kynar Finish,Window Color=Not Selected
33 1/2,56 1/2
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head, j
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Line Qty Product Description Dealer Price I
Extended
1700-2 4 TTT Frame Size: 33 1/2"x 56 1/2"
Notes:
Mark: B14
MISC/TRIM 3
Line Qty I Product Description Extended Dealer Price I
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 14 of 26
1800-1 2 TTT Frame Size: 34"
x 41"Notes:
Mark: B15
***PRODUCT***
Series 700 Awning Project Out Awning 34 x 41
***OPERATORS*** J
Cam Handles /
***HARDWARE
Four Bar Hinge tf
***COLOR*** \
70%Kynar Finish,Window Color=Not Selected
***SCREEN***
Standard Screen,Exterior Applied,Full Window,Aluminum
Mesh
***GLASS***
Double IG,RLE Softcoat,1 1/8"IG,No Gas,Inside Lite:
1/8",Outside Lite:1/8"
34,41
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,
DS113@ LJ,DS113@ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804a RJ,Tdm804@ Sill
Line I Qty I Product Description Dealer Price I
Extended
1800-2 2 TTT Frame Size: 34"x 41"
Notes:
Mark: B15
MISC/TRIM 3
Line Qty Product Description
Dealer Price I
Extended
1900-1 1 TTT Frame Size: 30"x 44"
Notes:
Mark: B16
***PRODUCT***
Series 550 Double Hung Operable 30 x 44 n
Even Sash Split***SCREEN*** �4
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh s
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts, U
Include Sash Lock=Yes,Pole Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),55ODH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,1"IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR'**
70%Kynar Finish,Window Color=Not Selected
30,44
***Wrapping Surcharges***
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 15 of 26
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Tdm804@ LJ,Tdm804@ RJ,Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 16 of 26
Line ! Qty ! Product Description ! Dealer Price I Extended]
TTT Frame Size: $
Notes: 54.00
Mark:
MISC/TRIM 3
1900-2 1 30"x 44"
B16
Line ! Qty ! Product Description
!Extended Dealer Price 1
2000-1 1 TTT Frame Size: 23"
x 44"Notes:
Mark: B17
***PRODUCT ---
Series 550 Double Hung Operable 23 x 44 I�
Even Sash Split JFJ
***SCREEN***
Standard Screen,Exterior Applied,Half Window,Aluminum
Mesh a
***HARDWARE***
Auto Lock+Spring=Yes,Full Length Rail=Yes,Top
Balance-Block and Tackle,Bottom Balance-Ultralifts,
Include Sash Lock=Yes,Pale Op Sash Lock
***Extrusion Picker***
550DH Header=Standard Header(400-101),550DH Left J
Jamb=Standard Jamb(400-103),550DH Right Jamb=
Standard Jamb(400-103),55ODH Sill=Auto Lock(400-125)
***GLASS***
Double IG,RLE Softcoat,V IG,Argon Gas Fill,Inside Lite:
1/8",Outside Lite:1/8"
***COLOR**'
70%Kynar Finish,Window Color=Not Selected
23,44
***Wrapping Surcharges***
Factory Attached Wrapping !
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,
Pan925@ LJ,Pan925@ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Line ! City ! Product Description
! Dealer Price I
Extended
2000-2 1 TTT Frame Size: 23"x 44"
Notes:
Mark: B17
MISC/TRIM 3
Line ! Qty ! Product Description
! Dealer Price I
Extended
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 17 of 26
2100-1 2 TTT Frame Size: 49"
x :Notes:
Mark: C
***PRODUCT***
Series 550 Direct Set Fixed 49 x 65
***HARDWARE***
Include Sash Lock=Yes
***GLASS*** ta
Double IG,RILE Softcoat,1"IG,No Gas,Inside Lite:3/16",
Outside Lite:3/16"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR*** ,
70%Kynar Finish,Window Color=Not Selected
49,65
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804a LJ,Tdm804 RJ,Trim804@ Sill
Line Qty Product Description Dealer Price I
Extended
2100-2 2 TTT Frame Size: 49"x 65"
Notes:
Mark: C
MISC/TRIM 3
Line Qty Product Description Dealer Price I
Extended
2200-1 2 TTT Frame Size: 49"x 73"
Notes:
Mark: C1
***PRODUCT***
Series 550 Direct Set Fixed 49 x 73
***HARDWARE***
Include Sash Lock=Yes
***GLASS`**
Double IG,RILE Softcoat,1"IG,No Gas,Inside Lite:3/16",
Outside Lite:3/16"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300) n
***COLOR***
70%Kynar Finish,Window Color=Not Selected
49,73
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ,Trim804@ RJ,Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 18 of 26
Line I Qty I Product Description
Dealer Price I Extended
2 TTT Frame Size:
Notes:
Mark:
MISC/TRIM 3
2200-2 49"x 73"
C1
Line I Qty I Product Description
Extended I Dealer Price I
2300-1 2 TTT Frame Size: 51 1/2"x
54 1/2"Notes:
Mark: C2 —
***PRODUCT*`*
Series 550 Direct Set Fixed 51 1/2 x 54 1/2
***HARDWARE***
Include Sash Lock=Yes
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8", a
Outside Lite:1/8"
***Extrusion Picker**
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
70%Kynar Finish,Window Color=Not Selected
51 1/2,54 1/2
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trirn804P LJ,Trim804 RJ,Trim804 Sill
Line I Qty I Product Description
Extended I Dealer Price I
2300-2 2 TTT Frame Size: 51 1/2"x 54 1/2"
Notes:Mark:
MISC/TRIM 3
Line I Qty I Product Description
Extended I Dealer Price I
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn
P Pages: 19 of 26
2400-1 1 TTT Frame Size: 44"x
39 1/2"Notes:
Mark: D ------------------
***PRODUCT***
Series 550 Direct Set Fixed 44 x 39 1/2
***HARDWARE***
Include Sash Lock=Yes
***GLASS***
Double IG,RLE Softcoat,Tempered,1"IG,No Gas,Inside x
Lite:1/8",Outside Lite:1/8"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR*** -----
70%Kynar Finish,Window Color=Not Selected
44,39 1/2
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,N/A @ Head,N/A @
LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Tdm804@ Sill
Lxe Qty Product Description
Eended
Dealer Price 1
2400-2 1 TTT Frame Size: 44"x 39 1/2"
Notes:
Mark: D
MISC/TRIM 3
Line I Qty I Product Description
Extended I Dealer Price 1
2500-1 2 TTT Frame Size: 85"x 56"
Notes:
Mark: E
***PRODUCT***
Series 550 Direct Set Fixed 85 x 56
***HARDWARE***
Include Sash Lock=Yes
***GLASS*** x
Double IG,Glass Type=SN68,1"IG,No Gas,Inside Lite:
1/4",Outside Lite:1/4"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb= az
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected
85,56
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ,Tdm804@ RJ,Tdm804@ Sill
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn
Pages: 20 of 26
Line I Qty I Product Description I Dealer Price I Extended
2 TTT Frame Size:
Notes:
Mark:
MISC/TRIM 3
2500-2 85"x 56"
E
Line I Qty I Product Description
Extended I Dealer Price 1
2600-1 2 TTT Frame Size: 45 13/32"
x 21"Notes:
Mark: T1
***PRODUCT***
Series 550 Direct Set Fixed 45 13/32 x 21
***HARDWARE*** --
Include Sash Lock=Yes
***GLASS
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***Extrusion Picker*** 1
550FX Header=Standard(400-300),550FX Left Jamb --
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected
***GRIDS***
Grids,Standard Rectangular,GBG:Grid-105,Exterior:
None,Interior:None,Grid Frame Only=No,Grid Color=
Window Exterior Color Same,5W2H
45 13132,21
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804 RJ,Trim804@ Sill
Line I Qty I Product Description
Extended I Dealer Price 1
2600-2 2 TTT Frame Size: 45 13/32"x 21"
Notes:Mark:
MISC/TRIM 3
Line I Qty I Product Description
Extended I Dealer Price I
Quoted by:RobertQuinn Printed by: Robed Quinn Safes Rep:Robert Quinn Pages: 21 of 26
2700-1 4 TTT Frame Size: 28"
x 21"Notes:
Mark: T2
***PRODUCT***
Series 550 Direct Set Fixed 28 x 21
***HARDWARE***
Include Sash Lock=Yes
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***Extrusion Picker**
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300) —
***COLOR***
70%Kynar Finish,Window Color=Not Selected
***GRIDS***
Grids,Standard Rectangular,GBG:Grid-105,Exterior:
None,Interior:None,Grid Frame Only=No,Grid Color=
Window Exterior Color Same,3W1H
28.21
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804 RJ,Tdm804@ Sill
Line Qty Product Description
Extended Dealer Price I
2700-2 4 TTT Frame Size: 28"x 21"
Notes:Mark:
MISC/TRIM 3
Line Qty Product Description
Extended � Dealer Price I
2800-1 2 TTT Frame Size: 85"x 21 1/2"
Notes:
Mark: T3
***PRODUCT***
Series 550 Direct Set Fixed 85 x 21 1/2
***HARDWARE***
Include Sash Lock=Yes ) �1
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8",
Outside Lite:1/8"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected 85,21 112
***Wrapping Surcharges***
Factory Attached Wrapping
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 22 of 26
I
Line I Qty I Product Description I Dealer Price I 6dended
2 TTT Frame Size:
Notes:
Mark:
MISC/TRIM 3
Wrapping 2 Factory Attached?=Yes,DS113@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804@ LJ,Tdm804@ RJ,Trim804@ Sill
2800-2 85"x 21 1/2"
Line I Qty I Product Description
Extended I Dealer Price I
2900-1 4 TTT Frame Size: 33 1/2"x
21 1/2"Notes:
Mark: T4
***PRODUCT***
Series 550 Direct Set Fixed 33 1/2 x 21 1/2 T
***HARDWARE***
Include Sash Lock=Yes
*GLASS
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8", ry
Outside Lite:1/8"
***Extrusion Picker*** HT I
550FX Header=Standard(400-300),550FX Left Jamb=
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected
***GRIDS***
Grids,Standard Rectangular,GBG:Grid-105,Exterior:
None,Interior:None,Grid Frame Only=No,Grid Color=
Window Exterior Color Same,3W2H
33 1/2,21 1/2
—Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Trim804 RJ,Tdm804 Sill
Line I Qty I Product Description
Extended I Dealer Price 1
2900-2 4 TTT Frame Size: 33 1/2"x 21 1/2"
Notes:Mark:
MISC/TRIM 3
Line I Qty I Product Description
Extended I Dealer Price I
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn
Pages: 23 of 26
3000-1 2 TTT Frame Size: 51 1/2"x
21 1/2"Notes:
Mark: T5
***PRODUCT***
Series 550 Direct Set Fixed 51 1/2 x 21 1/2
***HARDWARE***
Include Sash Lock=Yes
***GLASS***
Double IG,RLE Softcoat,1"IG,No Gas,Inside Lite:1/8", 1
Outside Lite:1/8"
***Extrusion Picker***
550FX Header=Standard(400-300),550FX Left Jamb
Standard(400-300),550FX Right Jamb=Standard
(400-300),550FX Sill=Standard(400-300)
***COLOR***
70%Kynar Finish,Window Color=Not Selected
***GRIDS***
Grids,Standard Rectangular,GBG:Grid-105,Exterior:
None,Interior:None,Grid Frame Only=No,Grid Color=
Window Exterior Color Same,6W2H
51 1/2,21 1/2
***Wrapping Surcharges***
Factory Attached Wrapping
Wrapping 2 Factory Attached?=Yes,DS113@ Head,N/A
@ LJ,N/A @ RJ,N/A @ Sill
Wrapping 1 Factory Attached?=Yes,Pan925@ Head,N/A
@ LJ,N/A @ RJ,Pan977@ Sill
Wrapping 3 Factory Attached?=No,Trim804@ Head,
Trim804 LJ,Tdm804 RJ,Trim804@ Sill
Line Qty Product Description
Extended Dealer Price 1
3000-2 2 TTT Frame Size: 51 1/2"x 21 1/2"
Notes:Mark:
MISC/TRIM 3
Line Qty I Product Description
Extended Dealer Price 1
3100-1 40
Notes:Mark:
Attic Stock Sash
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 24 of 26
Line Qty I Product Description Dealer Price I Extended
Notes:
Mark:
3200-1 5
Sets of Hinges
Line Qty I Product Description
Extended Dealer Price 1
3300-1 20
Notes:Mark:
Locks&Handles-Screws
Line Qty I Product Description
Extended Dealer Price 1
3400-1 1
Notes:Mark:
Gallon Paint
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn
Pages: 25 of 26
Line Qty I Product Description Dealer Price I
Extended
3500-1 16
Notes:Mark:
Mull Cover-119 Ivory K70
119-51/2"2pc Mull Cover Ivory Kynar 70%
Length:192 IN
Thank you for the opportunity to quote your project. Sub Total:
Shipping:
MATERIALS ONLY
Tax:
Installation -Anchors - Flashing -Shop Drawings -Field Measurements
NOT INCLUDED UNLESS NOTED ABOVE Total:
THIS QUOTED PRICE GOOD FOR 30 DAYS
Quoted by:RobertQuinn Printed by: Robert Quinn Sales Rep:Robert Quinn Pages: 26 of 26